Type to search



Tips for Installation and Maintenance of Your Water Heater

Your Opinion

5
3 Min Read

The utility of water heaters, also known as a geyser, in several Indian households, significantly increases during winters. Whether you buy a new water heater or are using an old one, it’s essential to install it properly and take care of it at the same time. But Summer is the right time to buy a new Water Heater with a great discount.

This blog will focus on crucial installation and maintenance tips that will prolong the life of your geyser. Let’s get started.

Installation of Water Heater

If you are installing a new geyser, there are certain things that you need to keep in mind. Some vital factors to consider are:

  • Ample space around the geyser

This is an essential lookout during geyser installation. Make sure there’s enough space between the walls and the apparatus. If there isn’t ample space, it makes it difficult for the technician to repair it should the need arise.

Also, as most geysers are placed on top of toilets, the same makes it difficult for the technicians to access them. Therefore, make sure to install it in the portion of the wall with nothing below it. Also, ensure that the heater is away from damp areas such as bathtub, shower, etc. Doing so will make it easily accessible.

  • Ensure installation at a sufficient height

This is another vital consideration during installation. If the geyser isn’t installed at an adequate height, the water pressure wouldn’t be sufficient, and instead of a strong gush, you will get only trickles from the tap. Hence, make sure the heater is at least 2 meters above the floor.

  • Take care of electrical switches and connections
READ  Recycle Waste Water With These Plumbing Hacks

As the geyser will operate on electricity, it’s vital to take care of the electrical connections during installation. Make sure to connect the water heater to the MCB that cuts electricity in case of power fluctuations. Also, keep the MCB at a height that makes it difficult for children to reach it but not for adults.

Also, during installation, if there are any electrical wires at the top of the heater, do disconnect them to prevent accidental shocks. It’s also a good idea to cap the wires to avoid confusion.

Maintenance of Water Heater

Now that you know how to install your water heater, let’s look at the maintenance tips for water heater that you must follow to ensure it’s proper working. Some essential points to remember are:

  • Avoid keeping the geyser on for long periods

This is an absolute no. Most people tend to keep their water heaters on for an extended period, especially during the morning. They feel that since everyone would need warm water, doing so will save time. However, this is a wrong notion.

If you keep your geyser on for extended periods, the same will reduce its lifespan. So, if you need warm water within minutes, make sure not to switch on your geyser half an hour earlier. Modern water heaters can heat water to the desired levels within 4-5 minutes after they are switched on. Following this tip will help you enhance the lifespan of your geyser.

  • Set a lower temperature

Often people set high-temperature levels on their geysers. However, note that the geyser is intended to give hot water and not boiling one. Setting a lower temperature has twin benefits. It lowers pressure on the geyser and at the same time saves electricity.

READ  6 Uses for Microwave That Will Surprise You For Sure..

Another important benefit is that it prevents accidental burns from extremely hot water. Thus, it’s prudent to set the temperature on the geyser at lower levels.

  • Replacing the corroded anode rod inside the geyser

Geysers have an anode rod inside the tank that attracts impurities and rust thereby preventing the tank from getting corroded. However, the rod itself gets corroded in the process. Therefore, you need to check the anode rod every 2 to 3 years and make sure it’s in proper shape.

If you see the outer layer of magnesium getting corroded and the inner steel core visible, then replace the anode rod immediately. Also, if the thickness of the rod has reduced considerably, then change it at the earliest.

  • An eye on the pressure release valves

A vital part of geyser maintenance is the working of the pressure release valves. Release the pressure a few times to know the valve’s condition. In case of the valve leaks, then it’s a matter of concern. Call a technician and get the valve replaced immediately.

In Conclusion

Equally essential is to get the annual maintenance of your geyser done to ensure its proper working. Make sure to get it done by an expert and authorised technician rather than doing it yourself.

Leave a Comment


check modal

Post Comment

X

Your comment is awaiting for moderation

Tags: